Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
my first printer
#31
(2018-07-23, 06:18 PM)evilpoly Wrote: i cut myself someĀ  single pane 3mm glass today . grinded the sides with a diamond grinder in water with my dremel . ugly job . but it fits . barely . id say just pay the guy $20 and have him custom cut you a piece. course it was more fun my way.

So this sits on top of the lcd facing the vat? 3mm glass the same dimensions as the lcd is that correct?
Reply


Messages In This Thread
my first printer - by evilpoly - 2018-06-29, 03:18 AM
RE: my first printer - by MisterAcoustic - 2018-06-30, 12:44 AM
RE: my first printer - by evilpolygon - 2018-07-15, 04:47 PM
RE: my first printer - by evilpoly - 2018-07-17, 10:40 PM
RE: my first printer - by evilpoly - 2018-07-18, 02:02 AM
RE: my first printer - by evilpoly - 2018-07-18, 03:23 AM
RE: my first printer - by evilpoly - 2018-07-18, 12:29 PM
RE: my first printer - by evilpoly - 2018-07-18, 01:29 PM
RE: my first printer - by evilpoly - 2018-07-18, 07:56 PM
RE: my first printer - by evilpoly - 2018-07-18, 08:02 PM
RE: my first printer - by evilpoly - 2018-07-19, 12:23 PM
RE: my first printer - by evilpoly - 2018-07-19, 12:37 PM
RE: my first printer - by evilpoly - 2018-07-19, 04:18 PM
RE: my first printer - by evilpoly - 2018-07-19, 08:15 PM
RE: my first printer - by evilpoly - 2018-07-20, 05:46 PM
RE: my first printer - by evilpoly - 2018-07-21, 05:56 PM
RE: my first printer - by evilpolygon - 2018-07-22, 07:07 AM
RE: my first printer - by evilpoly - 2018-07-23, 06:18 PM
RE: my first printer - by Elk - 2018-10-27, 12:14 AM
RE: my first printer - by evilpoly - 2018-07-23, 06:31 PM
RE: my first printer - by evilpolygon - 2018-07-25, 01:59 PM
RE: my first printer - by MisterAcoustic - 2018-07-26, 09:07 PM
RE: my first printer - by evilpolygon - 2018-07-27, 08:35 AM
RE: my first printer - by evilpolygon - 2018-07-27, 11:54 AM
RE: my first printer - by evilpolygon - 2018-07-27, 08:13 PM
RE: my first printer - by evilpolygon - 2018-07-28, 12:50 AM
RE: my first printer - by b0kkie - 2018-07-28, 07:32 PM
RE: my first printer - by evilpolygon - 2018-07-29, 04:06 AM
RE: my first printer - by evilpolygon - 2018-07-29, 04:34 AM
RE: my first printer - by Raccoon3D - 2018-08-11, 11:31 PM
RE: my first printer - by Raccoon3D - 2018-08-11, 11:35 PM

Forum Jump:


Users browsing this thread: 3 Guest(s)